# Types of Gas Turbine Engines

- Link: https://studyelectrical.com/2018/04/types-of-gas-turbine-engines.html
- Published: 2018-04-26T07:16:00+00:00
- Author: 

For an individual generator that is rated above 1000 kW, and is to be used in the
oil industry, it is usual practice to use a gas turbine as the driving machine (
also called the prime mover).

 Below 1000 kW a diesel engine is normally preferred usually because it is an emergency
generator running on diesel oil fuel. There are different types of gas turbine-driven
generators. Gas turbines can be classified in several ways, common forms are:-

 * Aero-derivative gas turbines.
 * Light industrial gas turbines.
 * Heavy industrial gas turbines.

## Aero-derivative Gas Turbines

 Aircraft engines are used as ‘gas generators’, i.e. as a source of hot, high-velocity
gas. This gas is then directed into a power turbine, which is placed close up to
the exhaust of the gas generator. The power turbine drives the generator.

  |  [⌊Aero derivative%2BGas%2BTurbines⌉](https://4.bp.blogspot.com/-euw3jdvOhdg/WuFzWyZLSqI/AAAAAAAABB8/DHJZm_geO14HGvvGj8vWIhfFlIOvYrQZwCLcBGAs/s1600/Aero-derivative%2BGas%2BTurbines.PNG) |  
 |  Aero-Derivative Gas Turbine  |

### Advantages of Aero-derivative Gas Turbines

The benefits of this arrangement are:-

 * Easy maintenance since the gas generator can be removed as a single, simple module.
   This can be achieved very quickly when compared with other systems.
 * High power-to-weight ratio, which is very beneficial in an offshore situation.
 * Can be easily designed for single lift modular installations.
 * Easy to operate.
 * They use the minimum floor area.

### Disadvantages of Aero-derivative Gas Turbines

The main disadvantages of Aero-derivative Gas Turbines are:-

 * Relatively high costs of maintenance due to short running times between overhauls.
 * Fuel economy is usually lower than other types of gas turbines.
 * The gas generators are expensive to replace.

Aero-derivative generators are available in a single unit form for power outputs
from about 8 MW up to about 25 MW. These outputs fall conveniently into the typical
power outputs required in the oil and gas production industry, such as those on 
offshore platforms.

## Light Industrial Gas Turbines

Some manufacturers utilize certain of the advantages of the aero-derivative machines,
i.e. high power-to-weight ratio and easy maintenance. 

 

The high power-to-weight ratios are achieved by running the machines with high combustion
and exhaust temperatures and by operating the primary air compressors at reasonably
high compression ratios i.e. above 7. 

![Light%2BIndustrial%2BGas%2BTurbines](https://3.bp.blogspot.com/-9qgyHNPKHcE/WuF04cl7leI/
AAAAAAAABCM/2A1YiGuxmhQmePVXGO72zPmASISNbRjjwCLcBGAs/s1600/Light%2BIndustrial%2BGas%
2BTurbines.jpg)

A minimum of metal is used and so a more frequent maintenance program is needed.
Easier maintenance is achieved by designing the combustion chambers, the gas generator,
and the compressor turbine section to be easily removable as a single modular type
of unit. 

 

The ratings of machines in this category are limited to about 10 MW.

## Heavy Industrial Gas Turbines

Heavy industrial gas turbines are usually to be found in refineries, chemical plants,
and power utilities.

 

They are chosen mainly because of their long and reliable running times between 
major maintenance overhauls. 

 

They are also capable of burning most types of liquid and gaseous fuel, even the
heavier crude oils. They also tend to tolerate a higher level of impurities in fuels.

  |  [⌊Heavy%2BIndustrial%2BGas%2BTurbines⌉](https://1.bp.blogspot.com/-jlHRm9DwGHU/WuF0EoNphAI/AAAAAAAABCE/scSqzq4EyP0K9kLAVFKFJ9gPbtsVGPNOACLcBGAs/s1600/Heavy%2BIndustrial%2BGas%2BTurbines.jpg) |  
 |  Heavy Industrial Gas Turbines |

 Heavy industrial machines are unsuitable for offshore applications because:-

 * Their poor power-to-weight ratio means that the structures supporting them would
   need to be much larger and stronger.
 * Maintenance shutdown time is usually much longer and is inconvenient because 
   the machine must be disassembled into many separate components. A modular concept
   is not possible in the design of these heavy industrial machines.
 * The thermodynamic performance is usually poorer than that of the light and medium
   machines. This is partly due to the need for low compression ratios in the compressor.

They do, however, lend themselves to various methods of heat energy recovery e.g.
exhaust heat exchangers, recuperators on the inlet air.

## Fuel for Gas Turbines

The fuels usually consumed in gas turbines are either in liquid or dry gas forms
and, in most cases, are hydrocarbons. 

 

In special cases, non-hydrocarbon fuels may be used, but the machines may then need
to be specially modified to handle the combustion temperatures and the chemical 
composition of the fuel and its combustion products.

 

Gas turbine internal components such as blades, vanes, combustors, seals and fuel
gas valves are sensitive to corrosive components present in the fuel or its combustion
products such as carbon dioxide, sulphur, sodium or alkali contaminants.

 

The fuel can generally be divided into several classifications:-

• Low heating value gas.

• Natural gas.

• High heating value gas.

• Distillate oils.

• Crude oil.

• Residual oil.

### Related posts:

No related posts.