# Functional Characteristics of Protective Relaying

- Link: https://studyelectrical.com/2015/11/fundamental-requirements-functional-characteristics-of-protective-relays.html
- Published: 2015-11-11T07:26:00+00:00
- Author: 

![fundamental%2Brequirements%2Bof%2Bprotective%2Brelaying](http://2.bp.blogspot.
com/-Vkn7HyjAvGg/VkHryjrPS-I/AAAAAAAAAOk/9_so9w1z7Vg/s1600/fundamental%2Brequirements%
2Bof%2Bprotective%2Brelaying.jpg)

The principal function of [protective relaying](https://studyelectrical.com/2018/09/classification-types-of-protective-relays.html)
is to cause the prompt removal from service of any element of the power system when
it starts to operate in an abnormal manner or interfere with the effective operation
of the rest of the system. 

In order that [protective relay](https://studyelectrical.com/2015/08/how-protective-electrical-relays-work.html)
system may perform this function satisfactorily, it should have the following qualities:

 1. Selectivity 
 2. Speed 
 3. Sensitivity
 4. Reliability
 5. Simplicity
 6. Economy

### Selectivity

_It is the ability of the protective system to select correctly that part of the
system in trouble and disconnect the faulty part without disturbing the rest of 
the system._

 * A well designed and efficient relay system should be selective i.e. it should
   be able to detect the point at which the fault occurs and cause the opening of
   the circuit breakers closest to the fault with minimum or no damage to the system.

This can be illustrated by referring to the single line diagram of a portion of 
a typical power system shown in the figure below. It may be seen that circuit breakers
are located in the connections to each power system elements in order to make it
possible to disconnect only the faulty section.

If a fault occurs at bus-bars on the last zone, then only breakers nearest to the
fault viz. 10, 11, 12 and 13 should open. In fact, the opening of any other breaker
to clear the fault will lead to a greater part of the system being disconnected.

  |  ⌊requirments%2Bof%2Bprotective%2Brelay⌉ |  
 |  Single Line Diagram of a portion of Power System |

In order to provide selectivity to the system, it is a usual practice to divide 
the entire system into several protection zones. When a fault occurs in a given 
zone, then only the circuit breakers within that zone will be opened. This will 
isolate only the faulty circuit or apparatus, leaving the healthy circuits intact.

The system can be divided into the following protection zones :

 * (a) generators 
 * (b) low-tension switchgear 
 * (c) transformers
 * (d) high-tension switchgear 
 * (e) transmission lines

It may be seen in the above figure that there is a certain amount of overlap between
the adjacent protection zones. For a failure within the region where two adjacent
zones overlap, more breakers will be opened than the minimum necessary to disconnect
the faulty section. 
  But if there were no overlap, a failure in the region between
zones would not lie in either region and, therefore, no breaker would be opened.
For this reason, a certain amount of overlap is provided between the adjacent zones.

### Speed

The relay system should disconnect the faulty section as fast as possible for the
following reasons :

 * Electrical apparatus may be damaged if they are made to carry the fault currents
   for a long time.
 * A failure on the system leads to a great reduction in the system voltage. If 
   the faulty section is not disconnected quickly, then the low voltage created 
   by the fault may shut down consumers motors and the generators on the system 
   may become unstable.
 * The high-speed relay system decreases the possibility of development of one type
   of fault into the other more severe type.

The ultimate goal of protective relaying is to disconnect a faulty system element
as quickly as possible. Sensitivity and selectivity are essential to assuring that
the proper circuit breakers will be tripped, but speed is the ‘pay-off’.

### Sensitivity

_It is the ability of the relay system to operate with a low value of actuating 
quantity._

The sensitivity of a relay is a function of the volt-amperes input to the coil of
the relay necessary to cause its operation.

 * The smaller the volt-ampere input required to cause relay operation, the more
   sensitive is the relay. 

Thus, a 1 VA relay is more sensitive than a 3 VA relay. It is desirable that the
relay system should be sensitive so that it operates with low values of volt-ampere
input.

### Reliability

_It is the ability of the relay system to operate under pre-determined conditions.
Without reliability, the protection would be rendered largely ineffective and could
even become a liability._
  That protective-relaying equipment must be reliable 
is a basic requirement. When protective relaying fails to function properly, the
allied mitigation features are largely ineffective.

Therefore, it is essential that protective-relaying equipment be inherently reliable,
and that its application, installation, and maintenance be such as to assure that
its maximum capabilities will be realized.

### Simplicity

The relaying system should be simple so that it can be easily maintained. Reliability
is closely related to simplicity. _The simpler the protection scheme, the greater
will be its __reliability._

### Economy

The most important factor in the choice of a particular protection scheme is the
economic aspect. Sometimes it is economically unjustified to use an ideal scheme
of protection and a compromise method has to be adopted. 

 * _As a rule, the protective gear should not cost more than 5% of the total cost._

However, when the apparatus to be protected is of utmost importance (e.g. generator,
main transmission line etc.), economic considerations are often subordinated to 
reliability.

 

### Related posts:

No related posts.